Oiicc DIY at Home

 Homemade flower decoration Materials: organzarn, glue, tree powder, 24# iron wire, pleated paper, clips, tape, lighter, pearl sticker 1. First complete the following graphic steps. (There will be offset printing when sticking iron wire and petals, and the overall view does not affect) 2. The stamen part can be decorated with pearl stickers. 3. The finished petals can be made into 2-3 small flowers, depending on the size and fullness of each flower. 4. The stamen and petals are superimposed in turn and wrapped with tape, and the tape part can be wrapped with excess organza to hide. 5. The iron wire of the flower stem part can be fixed with glue. You can also wrap another layer of floral paper tape. 6. The leaves can be added or not, because Tu saves trouble, so I went directly outside to pick up a few fallen leaves. Preferably dried leaves. 7. After it is done, it can be inserted in the vase. 8. If you want to insert it in a flower pot, you need to spread a piece of flower mud inside,

 Camellia paper art tutorial is here Material preparation: wrinkled paper, coloring pen, black paper art tape, white clay, white latex, iron wire, pliers, scissors. Tutorial: 1. Cut the red wrinkled paper into long strips. 2. Stack the strips on top of each other. 3. After cutting into squares, fold the square in half and cut the half-center shape. 4. After opening, stretch and shape the petals to make them more petal-shaped. 5. Prepare about 20-50 petals (according to your own preferences), all shaped and set aside. 6. Use pliers to cut a piece of iron wire to make a flower pole, and wind the flower pole with paper tape. 7. Cut a short strip out of yellow wrinkled paper and cut two-thirds into thin strips. 8. Knead the cut strips into strips by hand. 9. Evenly coat the bottom with white latex and roll on the flower stem. 10. Paste the petals, repeatedly pasting the petals in dislocation until the flowers are full. 11. Make the calyx, cut into small pieces with yellow or green wrinkled

 Paper Art Eustoma Materials preparation: crepe paper, iron wire, hot melt glue, scissors, paper craft tape. Production tutorial: 1. Cut a strip of crepe paper with a width of 4.5cm and fold it into a rectangle with a length of 6cm. 2. Fold the rectangle in half vertically and use scissors to cut half heart-shaped petals from the opened side. 3. Shape the petals. 4. Stretch the petals to make the petals more natural. 5. A flower has ten petals. 6. Use hot melt glue to glue the bottom right of the petals. 7. Overlap the petals and stick them together. 8. Paste according to the circle in turn. 9. Cut out the flower center with light green crepe paper, wind it and paste it on the iron wire. 10. Pass the flower center through the center of the petal, leaving 1/3 of the bottom. 11. Wrap the petals around the center of the flower and wrap it around the outside of the center of the flower. 12. Adjust the overall flower shape. 13. Make the calyx and paste it on the bottom of the flower. 14. Ad

 red paper art peony Material preparation: double-sided tape, scissors, thick crepe paper, iron wire, white latex, artificial stamens. Production tutorial: 1. Insert the three wires into the stamens respectively, and fix the top with double-sided tape. 2. Close the stamens and fix them with double-sided tape around them. 3. Cut long strips of crepe paper, fold them, and cut out petals according to the template. 4. Trim the wavy edges at the top of the petals. 5. Fold the petals in half and tighten them before unfolding to arrange the shape of the petals. 6. Paste double-sided tape on both sides of the bottom of the petals. 7. 10 large, medium and small petals each. 8. Combine the petals, first stick 10 small pieces, five pieces in one layer, paste the second layer in dislocation, and then paste larger petals. 9. Cut out five calyxes and paste them on the bottom of the flower. 10. To make leaves, cut two rectangles, one is coated with white latex, put the thin wire in the middle, and th